Plumbing Essentials: A Prerequisite for When Installing a Bathtub

Click Here

 

They are making a few great pointers relating to Tools You Need to Install a New Bathtub as a whole in this great article down below.


Tools You Need to Install a New Bathtub
Installing a bath tub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is also a moderately hard project. If the old bathtub is readily obtainable, the project can relocate speedily; if you need to open a wall surface to remove the old bathtub and position the new bathtub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also set in the new one. Make sure you have qualified on your own for the job as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Chances are you might require a professional plumber to make tube links.
This short article will help you install a brand-new bath tub in your bathroom if you have actually already bought a brand-new bathtub as well as don't need to transform the setup of your previous supply of water pipes.
Your tools as well as product checklist need to comprise the following:

 

  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  •  

Planning for the Setup


Firstly, the supporting frame provided with the bath should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.

 

 

Removing Old Taps


If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Bath tub


Utilizing the two wood boards under its feet, place the tub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by examining the level and readjusting the feet on the bath tub up until the spirit level reads degree.
To mount taps, fit the bottom of the furthest versatile faucet port to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system as well as check all joints and brand-new pipework for leaks and tighten them if necessary. Load the bath tub and additionally inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub should wait until the bathtub has been used at least once as this will certainly settle it into its last placement.

 

 

Fitting New Touches


If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Secure the faucet in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former kind should be linked to the tap ends first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bath tub


In the location where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to crack a stiff seal, causing the water to pass through the wall in between the bath and the tiling, bring about complications with wetness as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are sold in tubes as well as cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water-proof adhesive as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.


After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.


Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.


Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.


Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.


Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.


Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.


Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.


When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.


Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.


Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.


Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


How to Install a Bathtub

 

Do you like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a comment down the page. We will be delighted to hear your opinions about this page. In hopes that you visit us again before long. Do you know someone else who is truly interested in Installing A Bathtub? Be sure promote it. I thank you for reading our article about How to Install a Bathtub Yourself.


Toilet issues? Call!

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Plumbing Essentials: A Prerequisite for When Installing a Bathtub”

Leave a Reply

Gravatar